Skip to main content

what is the solar energy ?// needs of solar power//types of solar energy

 What is the solar energy?

Solar energy is the energy which is coming from Sun

This energy is the from of solar radiation that is producing a solar electricity.


Solar panels




Why do we need solar energy?

Because, solar power is free available from Sun and it does not produce pollution or green house gases. 

Its easy to install 



Type of solar energy

Photovoltaic solar power

Solar thermal energy

Concentrated solar power

Location: Unnamed Road, Jharkhand 815352, India

Comments

  1. Asad RajpootOctober 12, 2021 at 5:56 AM

    Hey Blogger mujhe contact kro telegram or +92 3458708509 my website magainnovations.com
    and https://pythonwithasad.blogspot.com

    ReplyDelete

Post a Comment

Popular posts from this blog

air preheater in thermal power plant - function , construction , working ,advantage , disadvantage

definition of air preheater air preheater increase the temperature  of the air. It is most commonly used in thermal power plant. And it is increase the efficiency of the boiler. Working of air preheaters (APH) 1. The hot fuel gas from the economist first enters the air preheater. Then those gases go through the tube to the chimney. The air mass then enters the preheater through the air inlet.  2.  Then both air and fuel gas flow in opposite directions.  3. baffles are provided in the air preheater to provide more time for exchanging heat from fuel gas to air   4. thus heat is absorbed by the air from the fuel gas. 5. this preheater air is supplied to the furnace.  construction   1. A tubular type air preheater is a large number of tube . 2. the fuel gas pass through the tube. 3. air flows over the tube. 4. baffles are provided to pass the air b number of time over the tube.  5. a soot hopper is provided at the bottom to collect the soo...
Post a Comment
Read more

Strain gauge || what is strain gauge ? || Working principle of strain gauge || Example-types of strain gauge

what is strain gauge ? A string gauge is a sensor which whose resistance varies with applied force.it converts force, pressure, tension weight e.t.c in to a Electrical resistance which can then be measured like pizo resistive transducer. Working principle of strain gauge : As we applied forced to extend the length of gauge it's cross section area must reduce becouse volume of material remain constant. Then strain gauge is connected to a balanced whiston  bridge but as force is applied on gauge resistance change and bridge becomes unbalanced producing V0                       Gauge factor Gf=1+2Y Y= paison ratio Using gauge factor we determined change in resistance to the modify resistance and then using Wheaton bridge V0 Examples : Gauge factor in semiconductor is 120 Gauge factor in Ni=12 Gauge factor in co=4.9 Gauge factor in pt=5.2 C=10 types of strain gauge 1. Straight strain checks.  2. Layer Rosette strain checks....
Post a Comment
Read more

Construction of silicon control rectifier (SCR)

 SCR- silicon control rectifier Construction 1. Anode and cathode region are highly drop where gate as moderately drop and drift layer are lightly drop. 2. SCR can be visualized as too BJT (PNP) and ( n p n) connected together 3. SCR is the minority carrier device and it has three p n junction . Disadvantage of SCR 1. Switching is very least while T-off highest  2. More switching loss 3. More conductivity modulation , least R-oN  4. Minimum oN state drop and minimum conductivity loss  # SCR contains three p n junction J1 anode and drift - anode is highly drop , depletion low J2 drift and gate - lightly drop , depletion low J3 gate and cathode - highly drop , depletion low Since there is light dropping on both side of J2  So breakdown voltage is high for junction J2  Reverse blocking Let ,            Anode is connected to negative terminal of supply which cathode is connected to positive terminal of supply  1. J1 and J2 rev...
Post a Comment
Read more